|
| TECH. DATA FOR 10,000 LBS. CAP. CARRIER
BODY DESIGN / CONSTRUCTION
A. BODY SLIDE SYSTEM. KILAR’S WRAP AROUND BODY SLIDE SYSTEM INCORPORATES A FULL LENGTH TUBULAR SUBFRAME INTEGRATED WITH A 6" @ 16 LBS. PER FT. WIDE FLANGE H BEAMS (ASTM A36). TENSILE STRENGTH OF BEAM , 60,000 – 80,000 P.S.I.. THE WRAP AROUND SLIDE SYSTEM COMBINES THE MECHANICAL STRENGTH OF BOTH THE H BEAM AND THE STRUCTURAL TUBE SUBFRAME OVER THE LENGTH OF THE BODY FOR GREATER RESISTANCE TO BODY FATIGUE AND BENDING. THE BODY H BEAMS SLIDE LATERALLY OVER GREASED RAILS AND REQUIRES ONLY NORMAL PERIODIC LUBRICATION.
B. BODY CROSS SILLS OR CROSS MEMBERS . 3" STRUCTURAL C CHANNEL (ASTM A36) SPACED ON 8" CENTERS
C. FLOOR.
1. 3/16" SMOOTH – STANDARD EQUIP.
2. 3/16" DIAMOND TREAD – OPTIONAL
3. APITONG HARD WOOD – OPTIONAL
D. APPROACH. – 24" STEEL INTEGRATED W/ 6- CHAIN SLOTS AND A "KNIFE EDGE " APPROACH
E. BODY WIDTH.
1. 95.5" WIDE O.D. – STANDARD
2. UP TO 102" O.D. – OPTIONAL
F .BODY SIDES.
1. 3" X 5" X 1/4" STRUCTURAL ANGLE (ASTM A36). W/ INSIDE STAKE POCKETS ON 24" CENTERS (NO RAISED RAILS)
2. WELDED RAISED OPEN RAILS 6" HIGH W/ OUT STAKE POCKETS
3. RUB RAIL OVER STAKE POCKETS ( BEST W/ 102" WIDE BODY)
4. CUSTOM SIDE AVAILABLE UPON REQUEST
G. CAB PROTECTOR. FULL HGT. FORMED W/ OPEN WINDOW , MECH. FASTENED TO BODY
1. STATIONARY FRAME MOUNTED CAB SHIELD AVAILABLE AS AN OPTION
H. WINCH. – 10,000 LBS. TULSA WORM GEAR W/ 50’X3/8" CABLE- STANDARD EQUIP.
I. BODY HOLD DOWN . – POSITIVE LOCK, ADJUSTABLE FOR WEAR.
J. ELECTRICAL. I.C.C. APPROVED. REAR SEALED TAIL LIGHTS IN AN ALUM. HOUSING , WATER TIGHT CONNECTORS
K. PAINT. TWO COAT URETHANE OVER EPOXY PRIMER . TECTILE UNDERCOATING ON THE BOTTOM SIDE OF DECK.
L. SUBFRAME.
1. PARALLEL TUBE GUIDE RAILS 2"x5"x 1/4" STRUCTURAL TUBE, ANGLE REINFORCED
2. 1.5" DIA. HINGE PIN IN DOUBLE SHEAR POINT
3. MIDSHIP MOUNTED DUAL TILT CYLS. ( INBOARD OF TRUCK FRAME FOR LOW DECK HGT.)
4. DUAL LIGHTED ALUMINUM CONTROL STATIONS
M. HITCH OPTIONS;
1. FIXED REAR BUMPER – STANDARD EQUIP.
2. HYD. DOCK LEG. – OPTIONAL
3. IND. HYD. TOW BAR – OPTIONAL
4. IND. HYD. WHEEL LIFT – OPTIONAL
5. 2" REESE TYPE RECEIVER TUBE – OPTIONAL
6. PINTLE HOOK- OPTIONAL
N. HYDRAULICS.
1. 3" BORE DOUBLE ACTING CYLS. W/ 2" CHROME RODS (2- BODY LIFT & 1- SLIDE CYL.)
2. POLY PACK STYLE PISTON SEALS
3. GEAR PUMP (16- 18 G.P.M.)
4. SECTIONAL STYLE CONTROL VALVE W/ BUILT IN RELIEF.
5. 2,000 P.S.I. SYSTEM PRESSURE.
KILAR MFG. RESERVES THE RIGHT TO IMPROVE OR UPGRADE ANY SPECS WITHIN WITHOUT NOTICE
|
| Carriers |
| 3 & 4 Car |
| Industrial |
| 1042 Wrecker |
| . |
 |
|
